Montgomery Decor

If you are planning to replace your old roof with new metal roofing, it would be very cost-efficient if you do it yourself. After all, anyone can learn how to install metal roofing. All you need is to learn the basics of tool-handling and pay attention to detail.

Now, to begin learning how to install metal roofing, we strongly recommend that you read through these very easy steps:

1. Get rid of the old material.

The initial task in how to install metal roofing is getting rid of the previous roofing, including all the nails. You can do this by using a pitchfork or shovel. Upon clearing the roof surface, you have to sweep the entire area with a broom to prepare it for the next step.

2. Roll out the roofing felt.

A 30-lbs. roofing felt needs to be laid out on the entire roof surface. Make sure the each sheet overlaps the previous one by a couple of inches, and that you leave about 3 inches hanging over each edge.

3. Create guidelines on the felt.

Draw parallel lines going from the crown of the roof to the gutter at two feet intervals from one another. You can do this using a chalk line. These straight lines will serve as guidelines when you are placing your metal sheets on the roof.

4. Attach the metal sheets.

If you feel you are confident enough and really know how to install metal roofing, then get ready because this is the biggest and most exciting part of the construction – installing the metal sheets. First, you have to cut a length of metal roofing equal to the distance from the crown to the edge of the roof, adding a couple of inches for the overhang. If you really want to learn how to install metal roofing, you also need to learn to measure accurately.

Lay down the first metal sheet on the leftmost side and attach it to the roof frame with screws every two feet. Repeat the same procedure for the next sheets until you have covered the whole roof. Make sure that each metal sheet overlaps the one beside it by about 2-3 inches.

5. Plug up the gaps.

Use a rubber strip to plug the lines where the metal sheets overlap. This will keep insects and other small animals from burrowing into your roof.

6. Attach the metal edging and cap.

Metal roofing is fast becoming a popular option for homeowners for a variety of reasons. In fact, metal roofing has a lot of advantages over other roofing materials. For one, the life of metal roofs is quite long. Metal roofs can last as long as the house itself if installed properly. This type of roof can seal out water, last through strong winds, and keep snow from accumulating on the roof.

Metal roofing is also resistant to fire, mildew, insects, and rot. Clearly, metal roofs offer a lot to the consumer, so it’s not surprising why they’re becoming more and more popular. And most companies guarantee their products for up to 50 years. Metal roofing materials are very lightweight as well. Because these roofs weigh so little, it’s even possible to apply the new roof over 1-2 existing roofs without taking down the old material or installing more structural support.

Another plus – metal roofing goes up quickly and easily. Most metal roofing materials arrive in sheets or sections of shingles, so someone with a decent amount of experience can throw them together in a very short amount of time. It is true, however, that you can purchase single metal shingles that are more expensive and time-consuming to install, so make sure you purchase the faster version.

The fire resistant quality of a metal roof is one of the most important advantages. Steel roofing is non-combustible, so it has been given a Class A fire rating – the highest a material can receive. But take note that if you will be applying a tin roof over a combustible material, such as wood shingles, the overall safety rating of your home will go down.

Steel roofing is made of metal, so it reflects radiant heat away from your house. This minimizes heat gain during the day, which has the potential to reduce energy costs in your home. This also benefits the environment. A tin roof is not as effective when it comes to insulation, but oftentimes contractors will leave some dead air space in between the tiles and the roof deck to allow for some insulation.

As you can see, metal roofing has a lot of advantages, but the one disadvantage is cost. The cost of metal roofing initially is on the expensive side. Comparable to other high-end materials, the price of metal roofing ranges from between $150 and $600 per 100 square feet. But the good news is that the price doesn’t necessarily make this material the most expensive option. You get back what you put in if you stay in the house for a long period of time, and don’t plan on moving anytime soon.

When it comes to metal roofing you have to make a decision – pay a little more for a high-quality product from the start and benefit from all it has to offer down the line, or choose another material that may end up costing you more in the long run? It’s all up to you, but after learning the facts, the choice should be clear.